Diplomat Chimney Fireplace Flue Heat Exchanger/Hot Air Exchanger, Exhaust Gas Cooler Black, XL Diameter 130 mm, 5 Pipes with Damper

£9.9
FREE Shipping

Diplomat Chimney Fireplace Flue Heat Exchanger/Hot Air Exchanger, Exhaust Gas Cooler Black, XL Diameter 130 mm, 5 Pipes with Damper

Diplomat Chimney Fireplace Flue Heat Exchanger/Hot Air Exchanger, Exhaust Gas Cooler Black, XL Diameter 130 mm, 5 Pipes with Damper

RRP: £99
Price: £9.9
£9.9 FREE Shipping

In stock

We accept the following payment methods

Description

Is there some thread or project folks can point me to that is similar, and was a successful heat exchanger? The down side to the multiple exhaust ports tapering to 1 is the possibility of turbulence restricting draw. There are several actions that could trigger this block including submitting a certain word or phrase, a SQL command or malformed data. I Canada I have seen the flue from a wood stove go across the kitchen ceiling, into the lounge then up through the floor and into the bedroom, across the room at shoulder height across the landing to the other bedroom and up out through the roof. in reading this thread, would it not be better to take small ammount away from the flue but have a coiled tube mounted to the back of the stove, that way you could save some of the rear radiated heat.

I wanted to build this heat exchanger to reclaim some of the heat that is lost up the chimney of my wood stove. Adding a condensing portion to a conventional boiler is frequently done on large commercial boilers. The one I was given after the service I'm sure was just combustion efficiency, it was just a probe in the exhaust gas stream so it had no idea how much heat was actually being passed in to the system. I started a fire in my outdoor fire pit, poked some holes in the bottom of the bucket, and placed the bucket upside down on the fire. Clean with a long handled, stiff bristled brush using soap and water, cleaning solvent, or a commercial soot remover.I dont mind stripping out a section of the flue to maintain it by cleaning the carbon off it every few months. A plate heat exchanger provides a means to pass heat from one system to the other without having to actually join the two systems.

SS is one of the least thermally-conductive materials you could make the HE out of (less than 1/3 as conductive as MS). I think the tiny fins between the core pipework would be sooted up in very quick time and aren't especially robust. What I'm trying to get you to see is that there are other reasonable and safe methods of saving energy that are available. Watertube systems of any kind, whether copper pipes wrapped around flues, or pipes running through flue gas, etc, seem like they would foul quickly and be really hard to clean.

Since I started with scrap steel, they were widely dissimilar thicknesses and the thin stuff kept burning through. The water from each system flows in sandwiched layers opposite each other with the heat passing from the hotter water to the cooler. I am considering TWO flue's in effect, with a Y and diverter baffle at the bottom, to duct the heat through the heating flue or through the straight up and out one. Between burning the same amount of wood (with the same amount of available BTU's) - I would think a fireplace would allow the most BTU's up the chimney, the heat exchanger the 2nd, and a proper stove the least amount of heat up the chimney = most heat in the room.

All of the products offered by Cheminées Poujoulat have been rigorously tested in every configuration by the CERIC Laboratory to ensure they meet highest standards (Building Regulation Document J - Amendments to Approved Documents). I wouldn't want to move that from the room my gas boiler is in though (bathroom, in the cupboard which previously housed bath towels and the like, I have just enough room left now for one shelf only 7. I have no illusions that this will be a long-lasting stove, or high efficiency, however it is certainly fun to build and so far cheap.

Most purchases from business sellers are protected by the Consumer Contract Regulations 2013 which give you the right to cancel the purchase within 14 days after the day you receive the item. Now insert the pin through both holes, turn on the saw and rotate the sheet metal around the center pin to cut a circle. The main reason fireplaces are so inefficient for heating a house is because you need to leave the flue open when you go to bed.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop